Mon, Mar 22, 2004
Trouble in Australia and Israel Compel Emergency AD
2004-06-52
Applicability: Model R22, R22 Alpha, R22 Beta,
and R22 Mariner helicopters, with a main rotor blade (blade), part
number (P/N) A016-1 or A016-2, installed, certificated in any
category.
Compliance: Required as indicated.
The FAA has sent an
Emergency AD notice to all US owners and operators of Robinson
Helicopter Company Model R22, R22 Alpha, R22 Beta, and R22 Mariner
helicopters.
According to FAA documents, this "Emergency Airworthiness
Directive (AD) is prompted by two accidents that occurred in
Australia and Israel that were attributed to failure of the main
rotor blade (blade). Investigation revealed that corrosion
from water penetration initiated a fatigue crack in a
blade. Information from the accident investigations revealed
that the cracked blades manifested an increase in helicopter
vibration. Following a track-and-balance of the blades, the
vibrations would go back to normal for a short time and then slowly
increase again until blade failure occurred. This condition, if not
prevented, could lead to a fatigue crack, blade failure, and
subsequent loss of control of the helicopter.
This unsafe condition is likely to exist or develop on other
helicopters of the same type design."
Therefore, this AD requires:
- Within 10 hours time-in-service (TIS) or 30 days, whichever
occurs first, track-and-balancing blades that are 5 years old or
have 1,000 hours TIS;
- Replacing the blades with airworthy blades before further
flight if an abnormal increase in vibration occurs within 5 hours
TIS after the last track-and-balance;
- Within 10 hours TIS or 30 days, whichever occurs first, for
helicopters with blades, part number (P/N) A016-1, replacing the
blades with airworthy blades other than blades, P/N A016-1, on or
before reaching 2,000 hours TIS;
- Within 10 hours TIS or 30 days, whichever occurs first, for
helicopters with blades, P/N A016-2, replacing the blades with
airworthy blades other than blades, P/N A016-1, on or before
reaching 2,200 hours TIS or 10 years, whichever occurs first;
and
- Within 10 hours TIS or 30 days, whichever occurs first,
determining the age of each blade and revising the component
history card or equivalent maintenance record for blades, P/N
A016-2, by adding a 10-year retirement life to the current 2,200
hours TIS retirement life.
This AD revises the Airworthiness Limitations section of the
applicable maintenance manual by adding a new retirement life of 10
years to the current 2,200 hours TIS retirement life. The blades
must be retired upon reaching 2,200 hours TIS or 10 years,
whichever occurs first.
FMI: Emergency AD 2004-06-52
More News
Aviation Governance Secured...At Least For a While The National Business Aviation Association similarly applauded the passage of the FAA's recent reauthorization, contentedly recou>[...]
Emphasis On Growing The Future of Aviation Through Concentration on 'AFFORDABLE FLYERS' It's been a number of years since the Latest Edition of Jim Campbell's HUGE SportPlane Resou>[...]
Amazilia Aerospace GmbH, Develops Digital Flight Control, Flight Guidance And Vehicle Management Systems Textron eAviation has acquired substantially all the assets of Amazilia Aer>[...]
Honeywell's Primus Brings New Tools and Niceties for Hawker Operators Hawker 4000 business jet operators have a new installation on the table, now that the FAA has granted an STC f>[...]
Company Celebrates Niche-but-Important Advancement in Industry Standards Echodyne has announced full integration of its proprietary 'EchoFlight' radar into the e American Aerospace>[...]