FAA Issues SAIB For Ice, Snow Ingestion For Rotorcraft | Aero-News Network
Aero-News Network
RSS icon RSS feed
podcast icon MP3 podcast
Subscribe Aero-News e-mail Newsletter Subscribe

Airborne Unlimited -- Most Recent Daily Episodes

Episode Date

Airborne-Monday

Airborne-Tuesday

Airborne-Wednesday Airborne-Thursday

Airborne-Friday

Airborne On YouTube

Airborne-Unlimited-12.09.24

Airborne-NextGen-12.10.24

Airborne-Unlimited-12.11.24

Airborne AffordableFlyers-12.12.24

Airborne-Unlimited-12.13.24

Tue, Jan 12, 2010

FAA Issues SAIB For Ice, Snow Ingestion For Rotorcraft

Procedures Reduce Probability Of An Engine Shutdown

The FAA has revised and reissued a Special Airworthiness Information Bulletin (SAIB) alerting owners and operators of turboshaft powered rotorcraft of the possibility of inflight engine loss of power due to the ingestion of ice and snow.  Accumulation of ice and snow can occur in the area of the airframe engine inlet while the rotorcraft is on the ground or in the air.

The FAA has determined that ingested ice and snow accumulation in the airframe engine inlet can cause the engine to lose power. This has resulted in accidents and fatalities. Snow and ice can build up in the engine intakes and plenums when the rotorcraft is on the ground with the engine(s) not operating or are operating at a low power setting for extended periods. When a pilot increases engine power during takeoff, the accumulated snow and ice can separate from the airframe inlet surface and be ingested into the engine, resulting in decreased power or complete engine failure. Some of the early turboshaft engines with axial inlets are particularly susceptible to loss of power due to ice and snow ingestion.

On the ground with the engine(s) operating at a low power setting, ice and snow can accumulate on the airframe cowl forward of the inlet, on the inlet lip, and inside the inlet. Under extreme conditions, usually when the rotorcraft is on the ground waiting for clear weather, the buildup of  ice and snow can be enough to cause the engine(s) to lose power or fail completely if the ice or snow is ingested.

On the ground with the engine(s) not operating, proper use of inlet inserts (pillows) or inlet covers can eliminate the accumulation of snow, but these measures cannot fully guarantee that ice will not form in the inlet. Ice can also develop in the inlet area when water seeps into the inlet  from rain or snow melting on a warm cowling, even when proper inlet protection is used.

Some rotorcraft require a snow protection kit for the airframe engine inlet in order to successfully operate in falling and blowing snow. Operation in snow without the kit is prohibited and can be especially risky when hovering in snow and then transitioning to takeoff when weather conditions
clear. Snow may accumulate on or in the engine inlet area during hover, and then be dislodged and ingested into the inlet during takeoff. Pilots should not believe they have escaped the danger following successful hover in snow with an unprotected inlet. If possible, land the aircraft immediately after the hover and thoroughly inspect the engine inlet prior to takeoff. If terrain will not allow an immediate safe landing, transition to takeoff as smoothly as possible when the weather clears with minimum application of engine power. Land and inspect the inlet area as soon as practical.

Most rotorcraft are NOT approved for flight in known icing (FIKI) conditions. For rotorcraft not approved for FIKI conditions, a pilot can expect icing any time when operating in visible moisture, such as fog, rain, or clouds, when the temperature is below 5°C [41°F]. Pilots should be aware  that icing is possible in these ambient conditions and should immediately leave the area of visible moisture or change to a warmer altitude. (NOTE: This “warmer” altitude may not always be a lower altitude.)

The FAA highly recommends the following procedures:

  • Review the aircraft Flight Manual for Limitations and Operations guidance in falling/blowing snow and/or icing. Many aircraft are prohibited from operating in known icing and/or falling and blowing snow.
  • Perform basic airmanship and preflight by evaluating current and predicted weather briefings from the area Flight Service Station. 
  • When the aircraft is on the ground without the engines operating, install inlet and exhaust inserts or covers.
  •  Prior to engine start, remove the inlet/exhaust inserts or covers and perform a complete inlet/exhaust inspection (using a flashlight). The inspection should include surfaces inside the inlet, the cowl area forward and around the inlet, and the area behind the particle separator or screen (if installed). Remove all accumulated snow or ice.
  • Do not remove ice or snow by chipping or scraping! Use heated air or deicing fluid as appropriate, in accordance with the manufacturer’s procedures. In freezing temperatures, pay particular attention to sheet ice on the bottom and forward of the inlet. This ice can also form behind particle separators. Engine preheating may be required.
  • Review Transport Canada Aviation Safety Letter Issue 4/2007 article 'Helicopter Operations: The Icing Factor'.

If it is necessary to keep the rotorcraft on the ground for an extended period (i.e., waiting for clear weather), you should shutdown the engine(s). Prior to takeoff, you should accomplish a detailed preflight inspection, removing any snow/ice build-up. You should perform the inspection even if the rotorcraft is fitted with some form of inlet protection, such as screens or baffles.

FMI: www.faa.gov

Advertisement

More News

Aero-News: Quote of the Day (12.10.24)

“We’re watching the very nature of warfare change. The speed of technology is absolutely meteoric.” Source: Maj. Gen. Clair Gill, commanding general of the Fort N>[...]

ANN's Daily Aero-Term (12.10.24): Handoff

Handoff An action taken to transfer the radar identification of an aircraft from one controller to another if the aircraft will enter the receiving controller's airspace and radio >[...]

ANN's Daily Aero-Linx (12.10.24)

Aero Linx: European Association of Aviation Training and Education Organizations – EATEO EATEO aspires to be the European voice for driving the best aviation training and edu>[...]

Aero-News: Quote of the Day (12.11.24)

“Think spacious modules with large windows to view Earth, our blue origin, while experiencing the thrill of weightlessness in complete comfort. Distinct quarters will be desi>[...]

ANN's Daily Aero-Term (12.11.24): Altitude Restriction

Altitude Restriction An altitude or altitudes, stated in the order flown, which are to be maintained until reaching a specific point or time. Altitude restrictions may be issued by>[...]

blog comments powered by Disqus



Advertisement

Advertisement

Podcasts

Advertisement

© 2007 - 2024 Web Development & Design by Pauli Systems, LC