When It Rains, It Pours... Another Lycoming AD | Aero-News Network
Aero-News Network
RSS icon RSS feed
podcast icon MP3 podcast
Subscribe Aero-News e-mail Newsletter Subscribe

Airborne Unlimited -- Most Recent Daily Episodes

Episode Date

Airborne-Monday

Airborne-Tuesday

Airborne-Wednesday Airborne-Thursday

Airborne-Friday

Airborne On YouTube

Airborne-Unlimited-05.06.24

Airborne-NextGen-04.30.24

Airborne-Unlimited-05.01.24 Airborne-AffordableFlyers--05.02.24

Airborne-Unlimited-05.03.24

Thu, May 18, 2006

When It Rains, It Pours... Another Lycoming AD

[Docket No. FAA-2005-21331; Directorate Identifier 2005-NE-07-AD; Amendment 39-14605; AD 2006-10-21]

ANN is looking over yet another Lycoming AD that was just published to the Federal Register, affecting a number of Lycoming 360 and 540 series engines, using ECi connecting rods.

According to the FAA, it is "adopting a new airworthiness directive (AD) for certain Lycoming Engines (formerly Textron Lycoming) 360 and 540 series reciprocating engines with ECi connecting rods, part number (P/N) AEL11750, installed. The Airmotive Engineering Corp, Division of Engine Components Incorporated (ECi), holds the Parts Manufacturer Approval (PMA) for the affected parts, and markets the parts as ECi parts."

"This AD requires replacing certain lot and serial numbered connecting rods, P/N AEL11750, having forging part number AEL11488. This AD would also prohibit installing certain ECi connecting rods, P/N AEL11750, into any Lycoming 360 or 540 series reciprocating engines. This AD results from reports of connecting rods with excessive variation in circularity of the journal bores. We are issuing this AD to prevent fatigue failure of the connecting rod and a possible uncommanded shutdown of the engine."

The AD becomes effective June 22, 2006.

In its final ruling, the FAA also addresses the comments made by many pilots that such an airworthiness directive is not needed, based on the relatively few incidents reported.

"Several commenters question the need for the connecting rod AD," the FAA stated. "We disagree. We confirmed that a manufacturing defect existed in the ECi connecting rods. The FAA has determined that this defect was the most probable cause of an engine shutdown and forced landing incident."

"ECi identified the manufacturing process deficiencies that were responsible for the defective condition and took specific actions to correct these deficiencies. We also determined that the subject ECi connecting rods in service could possess these manufacturing defects and could, therefore, fail during operation."

FMI: http://dms.dot.gov, AD 2006-10-21

Advertisement

More News

ANN's Daily Aero-Term (05.09.24): Hold Procedure

Hold Procedure A predetermined maneuver which keeps aircraft within a specified airspace while awaiting further clearance from air traffic control. Also used during ground operatio>[...]

ANN's Daily Aero-Term (05.06.24): Altitude Readout

Altitude Readout An aircraft’s altitude, transmitted via the Mode C transponder feature, that is visually displayed in 100-foot increments on a radar scope having readout cap>[...]

ANN's Daily Aero-Linx (05.06.24)

Aero Linx: European Hang Gliding and Paragliding Union (EHPU) The general aim of the EHPU is to promote and protect hang gliding and paragliding in Europe. In order to achieve this>[...]

Airborne-NextGen 05.07.24: AI-Piloted F-16, AgEagle, 1st 2 WorldView Sats

Also: Skydio Chief, Uncle Sam Sues, Dash 7 magniX, OR UAS Accelerator US Secretary of the Air Force Frank Kendall was given a turn around the patch in the 'X-62A Variable In-flight>[...]

Aero-News: Quote of the Day (05.07.24)

"The need for innovation at speed and scale is greater than ever. The X-62A VISTA is a crucial platform in our efforts to develop, test and integrate AI, as well as to establish AI>[...]

blog comments powered by Disqus



Advertisement

Advertisement

Podcasts

Advertisement

© 2007 - 2024 Web Development & Design by Pauli Systems, LC