NTSB Prelim: Bell 407 | Aero-News Network
Aero-News Network
RSS icon RSS feed
podcast icon MP3 podcast
Subscribe Aero-News e-mail Newsletter Subscribe

Airborne Unlimited -- Most Recent Daily Episodes

Episode Date

Airborne-Monday

Airborne-Tuesday

Airborne-Wednesday Airborne-Thursday

Airborne-Friday

Airborne On YouTube

Airborne-Unlimited-04.22.24

Airborne-Unlimited-04.16.24

Airborne-FlightTraining-04.17.24 Airborne-AffordableFlyers-04.18.24

Airborne-Unlimited-04.19.24

Join Us At 0900ET, Friday, 4/10, for the LIVE Morning Brief.
Watch It LIVE at
www.airborne-live.net

Sun, Jul 03, 2022

NTSB Prelim: Bell 407

About 30 Minutes Into The Flight, The Helicopter Experienced A Violent Upset

Location: Kalea, HI Accident Number: ANC22FA041
Date & Time: June 8, 2022, 17:26 Local Registration: N402SH
Aircraft: Bell 407 Injuries: 3 Serious, 3 Minor
Flight Conducted Under: Part 135: Air taxi & commuter - Non-scheduled - Sightseeing

On June 8, 2022, about 1726 Hawaii-Aleutian standard time, a Bell 407 helicopter, N402SH, sustained substantial damage when it was involved in an accident near Kalea, Hawaii, on the island of Hawaii. The pilot and two passengers sustained serious injuries, and three passengers sustained minor injuries. The helicopter was operated as a Title 14 Code of Federal Regulations Part 135 on-demand air tour flight.

According to a representative of the operator, Paradise Helicopters, about 1701, the helicopter departed the company base at Ellison Onizuka Kona International Airport at Keahole (PHKO), Kona, Hawaii, to the south for an air tour flight around the island. Automatic dependent surveillance-broadcast and company flight track data showed the helicopter traveled southeast about 500-600 ft above ground level and between airspeeds of 122 and 127 knots.

The pilot reported that the first part of the flight was normal; about 30 minutes into the flight, the helicopter experienced a violent upset, followed by an uncontrolled spin (yaw) to the right. A passenger, seated in the aft left forward-facing seat reported that as the helicopter continued to spin, she observed something fall off the helicopter; however, she was not able to identify a specific part.

The flight track data showed a rapid descent and decrease in airspeed at the end of the flight track, consistent with the occupants’ statements. The helicopter continued to spin uncontrollably while it descended, and it subsequently struck an area of rough, uneven, lava-covered terrain and came to rest on its left side.
After the impact, an emergency call was placed by a passenger to report that the helicopter had crashed.

An investigator from the National Transportation Safety Board's (NTSB) Alaska Regional Office, along with an NTSB airworthiness investigator, an NTSB survival factors investigator, and an NTSB maintenance investigator from Washington, D.C., responded to the island of Hawaii.

An NTSB on site examination of the accident site revealed the tail boom came to rest about 762 ft northeast from the main wreckage, which consisted of the fuselage, engine, and main rotor system. The tail boom separated from the fuselage at the tail boom attach point. The upper left attachment fitting fastener was not present, and the lower left attachment fitting was fractured and displayed fatigue signatures. The fasteners for the lower left, lower right, and upper right attachment fittings were present.

A review of the accident helicopter’s maintenance records revealed that the most recent tail boom attachment fasteners torque check (per Task #DMC-407-A-53-01-00-00A-72A) was completed on May 4, 2022, at a total airframe time of 22,891.4 flight hours. At the time of the accident, the helicopter had accumulated 23,005.6 flight hours (114.2 flight hours since the torque check), and no additional maintenance had been conducted to that attachment location. The tail boom (part number: 407-030-801-205D; serial number BP-1598) was installed on August 23, 2009, at a total airframe time of 5,780.0 hours and had not been removed prior to the accident.

Portions of the tail boom structure, aft fuselage structure, attachment fittings and fasteners were retained for further examination by the NTSB’s Materials Laboratory.

FMI: www.ntsb.gov

Advertisement

More News

ANN's Daily Aero-Term (04.24.24): Runway Lead-in Light System

Runway Lead-in Light System Runway Lead-in Light System Consists of one or more series of flashing lights installed at or near ground level that provides positive visual guidance a>[...]

ANN's Daily Aero-Linx (04.24.24)

Aero Linx: Aviation Without Borders Aviation Without Borders uses its aviation expertise, contacts and partnerships to enable support for children and their families – at hom>[...]

Aero-FAQ: Dave Juwel's Aviation Marketing Stories -- ITBOA BNITBOB

Dave Juwel's Aviation Marketing Stories ITBOA BNITBOB ... what does that mean? It's not gibberish, it's a lengthy acronym for "In The Business Of Aviation ... But Not In The Busine>[...]

Classic Aero-TV: Best Seat in The House -- 'Inside' The AeroShell Aerobatic Team

From 2010 (YouTube Version): Yeah.... This IS A Really Cool Job When ANN's Nathan Cremisino took over the lead of our Aero-TV teams, he knew he was in for some extra work and a lot>[...]

Airborne Affordable Flyers 04.18.24: CarbonCub UL, Fisher, Affordable Flyer Expo

Also: Junkers A50 Heritage, Montaer Grows, Dynon-Advance Flight Systems, Vans' Latest Officially, the Carbon Cub UL and Rotax 916 iS is now in its 'market survey development phase'>[...]

blog comments powered by Disqus



Advertisement

Advertisement

Podcasts

Advertisement

© 2007 - 2024 Web Development & Design by Pauli Systems, LC