Sat, Apr 24, 2021
AD 2021-09-04 Prompted By Reports Of An Oil Pump Blockage On E4 Model Diesel Piston Engines
The FAA is adopting a new airworthiness directive (AD) for all Austro Engine GmbH E4 and E4P model diesel piston engines.
This AD was prompted by reports of an oil pump blockage on E4 model diesel piston engines. This AD requires replacing a certain oil pump as well as the oil filter and engine oil. The FAA is issuing this AD to address the unsafe condition on these products. This AD is effective May 10, 2021.
Supplementary Information: The European Union Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community, issued EASA Emergency AD 2021-0055-E, dated February 25, 2021. EASA Emergency AD 2021-0055-E was revised by EASA AD 2021-0055R1, dated March 10, 2021. EASA AD 2021-0055R1 was superseded by EASA AD 2021-0094, dated March 31, 2021 (referred to after this as “the MCAI”), to address the unsafe condition on these products. The MCAI states:
- Occurrences were reported of oil pump blockage on E4-A and E4-B engines.
- Subsequent investigation determined that the blockage was caused by oil contamination with casting sand from the production process of oil pump P/N E4A50-000-BHY. A blocked oil pump causes failure of the engine lubrication system. The root cause was found in the sand casted oil pump housing cleaning process, which was not properly performed.
- This condition, if not corrected, could lead to engine in-flight shut-down with consequent forced landing, possibly resulting in damage to the aeroplane and injury to occupants.
- To address this potential unsafe condition, Austro Engine published the SB at original issue (later revised to add affected part s/n) to provide instructions to replace the affected oil pumps, and EASA issued AD 2021-0055-E to require replacement of affected parts, and replacement of the oil and filter. Subsequently, [EASA] AD 2021-0055R1 was issued to refer to the SB at Revision 2, where certain engines were removed from the applicability. The SB at Revision 2 also expanded the list of affected part s/n, but without impact on [EASA] AD compliance, as all added s/n were still in stock and would not be delivered to operators anymore. Since that [EASA] AD was issued, it was determined that affected parts are installed on additional engines, and Austro Engine published the SB at Revision 3 to correct the list of affected engine s/n. An additional oil pump replacement option was introduced with SB Revision 4 (with no further change to the list of affected engines/parts).
- For the reason described above, this [EASA] AD retains the requirements of EASA AD 2021-0055R1, which is superseded, and refers to the SB at Revision 4 (including the additional engine s/n and the new oil pump replacement option). This [EASA] AD also expands the Applicability to include all engines where the affected part is eligible for installation, and prohibits (re)installation of an affected part on all engines.
You may obtain further information by examining the MCAI in the AD docket at https://www.regulations.gov by searching for and locating Docket No. FAA-2021-0311.
More News
Runway Lead-in Light System Runway Lead-in Light System Consists of one or more series of flashing lights installed at or near ground level that provides positive visual guidance a>[...]
Aero Linx: Aviation Without Borders Aviation Without Borders uses its aviation expertise, contacts and partnerships to enable support for children and their families – at hom>[...]
Dave Juwel's Aviation Marketing Stories ITBOA BNITBOB ... what does that mean? It's not gibberish, it's a lengthy acronym for "In The Business Of Aviation ... But Not In The Busine>[...]
From 2010 (YouTube Version): Yeah.... This IS A Really Cool Job When ANN's Nathan Cremisino took over the lead of our Aero-TV teams, he knew he was in for some extra work and a lot>[...]
Also: Junkers A50 Heritage, Montaer Grows, Dynon-Advance Flight Systems, Vans' Latest Officially, the Carbon Cub UL and Rotax 916 iS is now in its 'market survey development phase'>[...]